ejecting

英 [iˈdʒektɪŋ]

美 [iˈdʒektɪŋ]

v.  驱逐; 逐出; 赶出; 喷出; 喷射; 排出; (飞行员在飞机坠毁前从弹射座椅)弹出
eject的现在分词

柯林斯词典

• VERB 驱逐;把…逐出
  If youejectsomeonefroma place, you force them to leave.
  1. Officials used guard dogs to eject the protesters...
     官员们用警犬驱散抗议人群。
  2. He was ejected from a restaurant.
     他被逐出餐厅。
• VERB 弹出;喷出;射出
  Toejectsomething means to remove it or push it out forcefully.
  1. He aimed his rifle, fired a single shot, then ejected the spent cartridge.
     他用步枪瞄准，射出一枚子弹，然后退出空弹壳。
• VERB （通常指飞行员从即将坠毁的飞机中）弹射出来
  When a pilotejects froman aircraft, he or she leaves the aircraft quickly using an ejector seat, usually because the plane is about to crash.
  1. The pilot ejected from the plane and escaped injury.
     飞行员从飞机中弹出，安然无恙。

双语例句

• During tape ejecting operation.
  在磁带弹出操作期间。
• Finally, the location and size of the ejector pins that correspond to the discrete ejecting forces are obtained.
  最后，这个位置和大小的异形销，迎合了离散排出力量。
• The North responded by ejecting international inspectors from the reprocessing facility at its main nuclear plant in Yongbyon.
  对此，北韩作出的回应是把国际核查员从它在宁边的主要核工厂驱赶出去。
• Would the eurozone be justified in ejecting Greece?
  欧元区逐出希腊是合理的吗？
• The mixing performance of cross flow was studied in turbine ejecting mixer with tracing technique.
  采用示踪法研究了涡轮喷射混合器内错流射流混合特征。
• The Study and Calculation of Gas Filling and Ejecting Characteristics of Gas-propelled APDS
  气推式脱壳弹充排气规律研究与计算
• Based on a double foundation characteristic, two schemes of high pressure ejecting grout plank wall and ballast for preventing piping and soil flow were investigated.
  根据双层地基的特点，分别对复合土工膜堆石堤堤基采用高压喷射灌浆板墙方案和压重防止管涌流土方案的防渗效果及经济性进行了计算比较。
• Some critics believe that World Cup games ought to use referees with experience ejecting superstars like Cristiano Ronaldo. '
  一些批评者认为，世界杯比赛使用的裁判一定要有把像C・罗纳尔多（CristianoRonaldo）那样的超级球星罚下场的经验。
• From this moment on the bolt group moves back at once, extracting and ejecting the spent case and chambering the fresh cartridge.
  从这片刻在门闩上立刻把移动聚集回来，吸取和逐放被花费的情形而且放在枪膛内新鲜的弹药筒。
• Througn designing three axial slots in internal threaded portion and optimizing nib structure, a design was made on the injection mould with a two-step ejecting mechanism with non-rotating.
  对笔尖内螺纹部分设计三段轴向开槽，优化笔尖结构，设计了二次推出不带旋转机构的自动脱螺纹注塑模。